Dell PowerEdge RAID Controller EM64T Device Driver for Windows Server 2003 x64 Editions Version 6.46.3.64 TABLE OF CONTENTS 1.0 Introduction 2.0 Compatibility / Minimum Requirements 3.0 Install Instructions 3.1 Installing the Driver During Operating System Installation 3.2 Updating an Existing Windows 2003 Driver 3.3 Installing a Windows 2003 Driver When Adding a New RAID Controller 4.0 Fixes or Enhancements in this Release 5.0 Additional Information 6.0 Revision History 1.0 Introduction ================ This is the driver for following PowerEdge Expandable RAID Controllers: PERC 4e/Di, 4e/Si, 4e/DC 4/DC, 4/SC 2.0 Compatibility / Minimum Requirements ======================================== This Device Driver is compatible with the following firmware versions: Controller Minimum Recommended Description Firmware Level PERC 4/SC 351Q PERC 4 Single Channel PERC 4/DC 351Q PERC 4 Dual Channel PERC 4e/Di 521Q PERC 4e Integrated on PE 2800, 2850, 6800, 6850 PERC 4e/Si 521Q PERC 4e Integrated on PE 1850 PERC 4e/DC 521Q PERC 4e Dual Channel 3.0 Install Instructions ======================== This is a self-extracting package of the Windows Server 2003 x64 device driver installation diskette for PERC 4/DC, 4/SC, PERC 4e/Di, PERC4e/Si and PERC 4e/DC. To build the installation diskette, execute the package and direct its output to an empty, formatted diskette. 3.1 Installing the Driver During Operating System Installation -------------------------------------------------------------- 1. Boot the system using the Microsoft Windows Server 2003 CD. 2. When the message Press F6 if you need to install a third party SCSI or RAID driver appears, press the key immediately. Within a few minutes, a screen appears that asks for additional controllers in the system. 3. Press the key. The system prompts for the driver diskette to be inserted. 4. Insert the driver diskette in the floppy drive and press the key. A list of PERC controllers appears. 5. Select the right driver for the installed controller and press the key to load the driver. NOTE: A message may appear that states the driver that you provided is older/newer then the Windows driver. Press the key to use the driver that is on the floppy diskette. 6. Press the key again to continue the installation process as usual. 3.2 Updating an Existing Windows 2003 Driver -------------------------------------------- Perform the following steps to update the Windows driver for the RAID controller already installed on your system. NOTE: It is important that you idle your system before you update the driver. 1. Press Start > Control Panel > System. The System Properties screen displays. 2. Click on the Hardware tab. 3. Click the Device Manager button and the Device Manager screen displays. 4. Click SCSI and RAID Controllers. 5. Double-click the RAID controller for which you want to update the driver. 6. Click the Driver tab and click on Update Driver. The screen for the Upgrade Device Driver Wizard displays. 7. Insert the appropriate driver diskette. 8. Click Next. 9. Follow the steps in the Wizard to search the diskette for the driver. 10. Select the name of the driver, not the INF file. 11. Click Next and continue the installation steps in the Wizard. 12. Click Finish to exit the wizard and reboot the system for the changes to take place. 3.3 Installing a Windows 2003 Driver When Adding a New RAID Controller ---------------------------------------------------------------------- Perform the following steps to configure the driver when you add the RAID controller to a system that already has Windows installed. 1. Power down the system. 2. Install the new RAID controller in the system. Refer to Hardware Installation for detailed instructions on installing and cabling the RAID controller in the system. 3. Power on the system. The Windows operating system should detect the new controller and display a message to inform the user. 4. The Found New Hardware Wizard screen pops up and displays the detected hardware device. 5. Click Next. 6. On the Locate Device Driver screen, select Search for a suitable driver for my device and click Next. 7. Insert the appropriate driver diskette and select Floppy disk drives on the Locate Driver Files screen. 8. Click Next. 9. The wizard detects and installs the appropriate device drivers for the new RAID controller. 10. Click Finish to complete the installation. 11. Reboot the server. 4.0 Fixes or Enhancements in this Release ========================================= Initial release of EM64T driver for Windows Server 2003 x64. 5.0 Additional Information ========================== 1. When installing Windows Server 2003 and have a PERC 4/DC, PERC 4/SC, PERC 4e/DC, PERC4e/Si or PERC 4e/Di together in a system, you will see the following selection when choosing a logical drive to configure. (xxxxx)mb Disk 0 at Id on bus on mraid35x [MBR] Where (xxxxx) is the size of the logical drive. Where (y) is the logical drive Id per controller. Where (z) is the bus number. If there is more than 1 logical drive per controller then Id number will be incremented. If there is more than 1 type of controller in a system then multiple selections will be displayed per controller. (xxxxx)mb Disk 0 at Id (y) on bus (z) on mraid35x [MBR] (xxxxx)mb Disk 0 at Id (y) on bus (z) on mraid35x [MBR] The user must be careful to select the appropriate Id when installing Windows Server 2003. 6.0 Revision History ==================== Initial release of EM64T driver for Windows Server 2003 x64.